TWS Flanged static balancing valve
Description:
TWS Flanged Static balancing valve is a key hydraulic balance product used for precise flow regulating of water pipelines system in HVAC application to ensure static hydraulic balance across whole water system. The series can ensure the actual flow of each terminal equipment and pipeline in line with the design flow in the phase of system initial commisiioning by site commissiong with flow measuring computer. The series are widely used in main pipes, branch pipes and terminal equipment pipelines in HVAC water system. It also can be use in other application with the same function requirement.
Features
Simplified pipe design and calculation
Quick and easy installation
Easy to measure and regulate water flowrate in site by the measuring computer
Easy to measure differential pressure in site
Balancing through stroke limitation with digital presetting and visible presetting display
Equipped with both pressure test cocks for differential pressure measurement Non rising hand wheel for convenience operation
Stroke limitation-screw protected by protection cap.
Valve stem made of stainless steel SS416
Cast iron body with corrosion resistant painting of epoxy powder
Applications:
HVAC water system
Installation
1.Read these instructions carefully. Failure to folow them could damage the product or cause a hazardous condition.
2.Check the ratings given in the instructions and on the product to make sure the product is suitable for your application.
3.Installer must be a trained, experienced service person.
4.Always conduct a thorough checkout when installation is completed.
5.For trouble-free operation of the product, good installation practice must include initial system flushing, chemical water treatment and the use of a 50 micron (or finer) system side stream filter(s). Remove all filters before flushing. 6.Suggest using a tentative pipe to do the initial system flushing. Then plumb the valve in the piping.
6.Do not use boiler additives, solder flux and wetted materials which are petroleum based or contain mineral oil, hydrocarbons, or ethylene glycol acetate. Compounds which can be used, with minimum 50% water dilution, are diethylene glycol, ethylene glycol, and propylene glycol (antifreeze solutions).
7.The valve may be installed with flow direction same as the arrow on the valve body. Wrong installation will lead to hydronic system paralysis.
8.A pair of test cocks attached in the packing case. Make sure it should be installed before initial commissioning and flushing. Make sure it isn’t damaged after installation.
Dimensions:
| DN | L | H | D | K | n*d |
| 65 | 290 | 364 | 185 | 145 | 4*19 |
| 80 | 310 | 394 | 200 | 160 | 8*19 |
| 100 | 350 | 472 | 220 | 180 | 8*19 |
| 125 | 400 | 510 | 250 | 210 | 8*19 |
| 150 | 480 | 546 | 285 | 240 | 8*23 |
| 200 | 600 | 676 | 340 | 295 | 12*23 |
| 250 | 730 | 830 | 405 | 355 | 12*28 |
| 300 | 850 | 930 | 460 | 410 | 12*28 |
| 350 | 980 | 934 | 520 | 470 | 16*28 |
Related products
-
TWS Flanged Y Strainer According to ANSI B16.10
Description: Y strainers mechanically remove solids from flowing steam, gases or liquid piping systems with the use of a perforated or wire mesh straining screen, and are used to protect equipment. From a simple low pressure cast iron threaded strainer to a large, high pressure special alloy unit with a custom cap design. Material list: Parts Material Body Cast iron Bonnet Cast iron Filtering net Stainless steel Feature: Unlike other types of strainers, a Y-Strainer has the advan...
-
Flanged Backflow Preventer
Description: Slight resistance Non-return Backflow Preventer (Flanged Type) TWS-DFQ4TX-10/16Q-D - is a kind of water control combination device developed by our company, mainly used for water supply from urban unit to the general sewage unit strictly limit the pipeline pressure so that the water flow can only be one-way. Its function is to prevent the backflow of the pipeline medium or any condition siphon flow back, in order to ...
-
MD Series Lug butterfly valve
Description: MD Series Lug type butterfly valve allows downstream pipelines and equipments online repair, and it can be installed on pipe ends as exhaust valve. Alignment features of lugged body allows easy installation between pipeline flanges. a real installation cost saving, can be installed in the pipe end. Characteristic: 1. Small in size&light in weight and easy maintenance. It can be mounted wherever needed. 2. Simple,...
-
EH Series Dual plate wafer check valve
Description: EH Series Dual plate wafer check valve is with two torsion springs added to each of pair valve plates, which close the plates quickly and automatically, that can prevent the medium from flowing back.The check valve can be installed on both horizontal and vertical direction pipelines. Characteristic: -Small in size, light in weight, compact in structure, easy in maintenance. -Two torsion springs are added to each of the pair valve plates, which close the ...
-
EZ Series Resilient seated NRS gate valve
Description: EZ Series Resilient seated NRS gate valve is a wedge gate valve and Non-rising stem type, and suitable for use with water and neutral liquids (sewage). Characteristic: -On-line replacement of top seal: Easy installation and maintenance. -Integral rubber-clad disc: The ductile iron frame work is thermal-clad integrally with high performance rubber. Ensuring tight seal and rust prevention. -Integrated brass nut: By mea...
-
EZ Series Resilient seated OS&Y gate valve
Description: EZ Series Resilient seated OS&Y gate valve is a wedge gate valve and Rising stem type, and suitable for use with water and neutral liquids (sewage). Material: Parts Material Body Cast iron,Ductile iron Disc Ductilie iron&EPDM Stem SS416,SS420,SS431 Bonnet Cast iron,Ductile iron Stem nut Bronze Pressure test: Nominal pressure PN10 PN16 Test pressure Shell 1.5 Mpa 2.4 Mpa Sealing 1.1 Mp...
