TWS Flanged Y Strainer According to ANSI B16.10

Short Description:

Size:DN 50~DN 300

Pressure:150 psi/200 psi

Standard:

Face to face:ANSI B16.10

Flange connection:ANSI B16.1


Product Detail

Product Tags

Description:

Y strainers mechanically remove solids from flowing steam, gases or liquid piping systems with the use of a perforated or wire mesh straining screen, and are used to protect equipment. From a simple low pressure cast iron threaded strainer to a large, high pressure special alloy unit with a custom cap design.

Material list: 

Parts Material
Body Cast iron
Bonnet Cast iron
Filtering net Stainless steel

Feature:

Unlike other types of strainers, a Y-Strainer has the advantage of being able to be installed in either a horizontal or vertical position. Obviously, in both cases, the screening element must be on the “down side” of the strainer body so that the entrapped material can properly collect in it.

Some manufactures reduce the size of the Y -Strainer body to save material and cut cost. Before installing a Y-Strainer, be sure it is large enough to properly handle the flow. A low-priced strainer may be an indication of an undersized unit. 

Dimensions:

"

Size Face to face Dimensions. Dimensions Weight
DN(mm) L(mm) D(mm) H(mm) kg
50 203.2 152.4 206 13.69
65 254 177.8 260 15.89
80 260.4 190.5 273 17.7
100 308.1 228.6 322 29.97
125 398.3 254 410 47.67
150 471.4 279.4 478 65.32
200 549.4 342.9 552 118.54
250 654.1 406.4 658 197.04
300 762 482.6 773 247.08

Why Use a Y Strainer?

In general, Y strainers are critical anywhere clean fluids are required. While clean fluids can help maximize the reliability and lifespan of any mechanical system, they’re especially important with solenoid valves. This is because solenoid valves are very sensitive to dirt and will only function properly with clean liquids or air. If any solids enter the stream, it can disrupt and even damage the entire system. Therefore, a Y strainer is a great complimentary component. In addition to protecting the performance of solenoid valves, they also help safeguard other types of mechanical equipment, including:
Pumps
Turbines
Spray nozzles
Heat exchangers
Condensers
Steam traps
Meters
A simple Y strainer can keep these components, which are some of the most valuable and expensive parts of the pipeline, protected from the presences of pipe scale, rust, sediment or any other kind of extraneous debris. Y strainers are available in a myriad of designs (and connection types) that can accommodate any industry or application.

 

  • Previous:
  • Next:
  • Write your message here and send it to us

    Related products

    • ED Series Wafer butterfly valve

      ED Series Wafer butterfly valve

      Description: ED Series Wafer butterfly valve is soft sleeve type and can separate the body and fluid medium exactly,. Material of Main Parts:  Parts Material Body CI,DI,WCB,ALB,CF8,CF8M Disc DI,WCB,ALB,CF8,CF8M,Rubber Lined Disc,Duplex stainless steel,Monel Stem SS416,SS420,SS431,17-4PH Seat NBR,EPDM,Viton,PTFE Taper Pin SS416,SS420,SS431,17-4PH Seat Specification: Material Temperature Use Description NBR -23...

    • TWS Air release valve

      TWS Air release valve

      Description: The composite high-speed air release valve are combined with two parts of high-pressure diaphragm air valve and the low pressure inlet and exhaust valve ,It has both exhaust and intake functions. The high-pressure diaphragm air release valve automatically discharges the small amount of air accumulated in the pipeline when the pipeline is under pressure. The low-pressure intake and exhaust valve can not only discharge...

    • DL Series flanged concentric butterfly valve

      DL Series flanged concentric butterfly valve

      Description: DL Series flanged concentric butterfly valve is with centric disc and bonded liner,and have all same common features of other wafer/lug series,these valves are featured by a higher strength of the body and better resistance to pipe pressures as safey factor. Having all same common features of the univisal series.  Characteristic: 1. Short Length pattern design 2. Vulcanised rubber lining 3. Low torque operation 4. St...

    • UD Series soft sleeve seated butterfly valve

      UD Series soft sleeve seated butterfly valve

      UD Series soft sleeve seated butterfly valve is Wafer pattern with flanges ,the face to face is EN558-1 20 series as wafer type. Characteristics: 1.Correcting holes are made on flange according to standard, easy correcting during the installation. 2.Through-out bolt or one-side bolt used. Easy replacing and maintenance. 3.The soft sleeve seat can isolate the body from media. Product operation instruction 1. Pipe flange standards ...

    • BD Series Wafer butterfly valve

      BD Series Wafer butterfly valve

      Description: BD Series wafer butterfly valve can be used as a device to cut-off or regulate the flow in various medium pipes. Through selecting different  materials of disc and seal seat, as well as the pinless connection between disc and stem,the valve can be applied to worse conditions, such as desulphurization vacuum, sea water desalinization. Characteristic: 1. Small in size&light in weight and easy maintenance. It can be...

    • AZ Series Resilient seated NRS gate valve

      AZ Series Resilient seated NRS gate valve

      Description: AZ Series Resilient seated NRS gate valve is a wedge gate valve and Non-rising stem type, and suitable for use with water and neutral liquids (sewage) . The non-rising stem design ensures the stem thread is adequately lubricated by the water passing through the valve. Characteristic: -On-line replacement of top seal: Easy installation and maintenance. -Integral rubber-clad disc: The ductile iron frame work is thermal...